R3  Mid-Feed Bodies & Inserts

R3 Mid-Feed End Mills

End Mills are solid steel, manufactured for coolant thru tool.

Toroid R3 End Mill
End Mills R3 –10mm IC
OD
Dia.
Holder R
Effective Length
L
Overall Length
S
Shank Dia.
Flutes DOC Recommended Insert CAD File
1.000" HFEM100-250-R3-2 2.500" 4.750" 1.000" 2 .015-.040" RF10 DXF
1.000" HFEM100-450-R3-2 4.500" 6.750" 1.000" 2 .015-.030" RF10 DXF
1.250" HFEM125-300-R3-3 3.000" 5.280" 1.250" 3 .015-.040" RF10 DXF
1.250" HFEM125-500-R3-3 5.000" 7.280" 1.250" 3 .015-.030" RF10 DXF
1.500" HFEM150-350-R3-3 3.500" 5.780" 1.250" 3 .015-.040" RF10 DXF
1.500" HFEM150-550-R3-3 5.500" 7.780" 1.250" 3 .015-.030" RF10 DXF

R3 Mid-Feed Shell Mills


R3 Mid-Feed Shell Mills
Shell Mills R3 – 10mm IC
OD
Dia.
Holder R
Effective Length
B
Arbor Dia.
H
Counter Bore Dia.
Flutes DOC Recommended Insert CAD File
2.000" HFSM200-075-R3-5C 1.500" .750" .590" 5 .015-.040" RF10 DXF
3.000" HFSM300-100-R3-6C 2.000" 1.000" .790" 6 .015-.040" RF10 DXF

Mid-Feed Inserts

T-Land Cutting Edge "T" inserts have a reinforced cutting edge for steels, irons and hard milling.
Dished Cutting Edge "D" inserts have a positive cutting geometry, designed to reduce cutting forces and heat. This edge is suitable for all materials.
"F" Cutting Edge NEW "F" inserts are specially reinforced for the heaviest feeds and most abusive applications in steels or irons (available in grade DMK30 only).
Mid-Feed Inserts
Insert IC Thickness # of Usable Edges Corner Radius (Actual) Corner Radius (Program) DOC (Max.) DOC (Recommended) FPT
(Compensated)
RF10-T 10MM .190" 4 .075" .105" .045" .015-.040" .020-.060"
RF10-D 10MM .190" 4 .075" .105" .045" .015-.040" .015-.050"
RF10-F 10MM .190" 4 .075" .105" .045" .015-.040" .025-.065"
* A special corner radius value is required for correct programming of a high-feed insert. Using the program radius avoids gouging of the corners in the workpiece material.
The high-feed insert will naturally leave a small amount of extra material at the bottom-most layer of the cut, at the intersection of the wall and pocket floor.
RHINO-FEED inserts are labeled with dots to indicate die position during pressing. For the most accurate runout when loaded into the cutter body, make sure each insert is loaded with the corresponding edge.

Click here for operating instructions for mid-feed inserts.

 
NEW "F" Geometry and TCI Grade!
 
 
Mid-Feed RF10 Grade Availability
Uncoated With Coating
DMK30
T, D, F
DMK30-GLH
T, D, F
DMK30-TCI
T, D, F
The older "HP" coating has been replaced by the new "TCI" grade. "HP" is available upon request, but will typically have a 1-2 week delivery time.
DMK25
D
DMK25-GLH
D
NEW GRADE!
DMP25
T, D
DMP25-GLH
T, D
DMP25-TCI
T
DMK15
T
DMK15-GLH
T
DMK15-TCI
T
Mid-Feed Inserts

A Proud USA Manufacturer